Acu-Cutter 350 Foam Cutter

Home > Tools > Cutters, Shears, Knives & Awls >

Larger Photo Email A Friend

Price per unit

Pricing starts at: $269.99

Volume or Out of stock quantities will typically ship within 1-3 business days.

Quantity in Stock:Out of Stock - Backorder

Availability: In stock orders ship same business day up to 4:00pm Central; otherwise usually ships within 3-5 Days
Item #: FOAM-CUTTER-350

Qty:

Description

Cleaning Instructions

Acu-Cutter 350
Dual Blades - One Moves

D e s i g n
The Acu-Cutter 350 is a simple multi purpose foam cutter that can cut most foams up to 8 ½ inches thick. The Acu-Cutter 350 has 2 blades, one stationery and one moving. The blades are made from ½ inch (front to back) “V” tooth blade material (10 teeth per inch) to produce a fine reliable cut. The Acu-Cutter 350 is also available as a 12 inch saw. Because foam saws are awkward to use, we do not recommend this unless your foam cutting requires the longer length.

F e a t u r e s *
Uses a detachable, low profile base with glide rollers This base can be removed to produce angle cuts or sculpting Powered with a 4.5 amp Black & Decker JS 500 jig saw motor with variable speed. Accordingly, these motors can be replaced at a low cost with ease and parts are readily available. Other more expensive foam cutters can cost $350 to replace a motor. Because the Acu-Cutter 350 motor can be replaced with ease, the Acu-Cutter 350 is the best choice today for a reliable high volume foam cutter.

Q u a l i t y
Pre-tested ready to use out of the box. Other cutters require the purchase of supplementary parts and assembly.

Simply put, the Acu-Cutter 350 is a relatively inexpensive, reliable, multi purpose foam cutter that can be easily serviced.

*60 Day Satisfaction Guarantee | 1 Year Warranty | Personal Customer Service

M o t o r   D e t a i l s
Volts    120 AC
Amps   4.5
Variable Speed    Yes
RPM   0 - 3,200
Stroke   11/16 Inch

C u t t i n g   S p e e d
It is not always necessary to run the motor at full speed to cut foam. You may wish to experiment with cutting at slower speeds. Slower speeds may create different cutting effects and increase the life of the saw.

B l a d e   S h a r p n e s s
The upper teeth of your saw do almost no cutting and the lower teeth are used almost always. With the saw turned off, run your fingers across the points of the teeth at the top and bottom and compare them to determine the amount of wear that has occurred to the lower teeth.

L u b r i c a t i o n
The moving blade should be occasionally lubricated with any lubricating oil. The purpose of the lubrication is to reduce heat and friction on both sides of the moving blade. Failure to do this will result in excess stress on the motor and shorten its useful life.
Stop the motor with the moving blade in the up position exposing about 1/2 inch of the blade at the top of its enclosure or blade guide.
Apply the lubricant to both sides of the moving blade at the top of the blade guide below the blade clamp.
The up and down motion of the moving blade will draw the oil down into the blade guide on either side of the blade.

S i l i c o n e   S p r a y
The blades may be sprayed frequently with a silicone spray. Silicone spray is effective when sprayed on the cutting edge of the blade to enable better penetration of the foam. As silicone residue and other debris may accumulate in the saw, you should remove the blades and clean the saw as needed.

B a s e   P l a t e
The base plate is attached by two high strength screws, which should be kept tight at all times to prevent breakage. If you are having any difficulty keeping these screws tight, you should immediately use Loctite (available through your hardware store).

For certain freehand cutting, you may wish to remove the base plate. This can be accomplished by loosing the two base screws and removing the base.

W a r r a n t y
The Manufacturer warrants this product for one year against any defects due to faulty material or workmanship. The unit should be returned complete, transportation prepaid, to the seller (or participating authorized distributor) for free replacement or repair. Proof of purchase may be required. This warranty does not apply to accessories, such as blades.

S e r v i c e
Phone 1 800 671 9853 to arrange service for your foam cutter.

Browse for more products in the same category as this item:

Tools > Cutters, Shears, Knives & Awls
Tools > Power Upholstery Tools